Rechargeable battery shields for Arduino - a quick review

Update Nov 2, 2011
Find an update to this post here.

Some time ago I purchased several shields for powering Arduinos from Li-Ion batteries.
They are:

My main requirement for such a shield was to have Arduino-form factor, so that I can just plug it into the Arduino, with no extra work required. Ideally, it would also have an on-board (attached) battery of at least 1000mAh.
Considering that the height of the headers in an Arduino shield is about 8mm and the space between them is about 43mm, the dimensions of the battery should not exceed 50mm x 43mm x 8mm.

None of the three solutions presented here met this requirement, at least not without modifications.


1. 5V DC-DC step-up power pack















This "power pack" shield comes with an on-board (attached) 1500mAh Li-Poly battery. The battery is wider than 43mm, so the headers are not (and cannot be) present. Therefore, the shield is not plug-able, which would technically disqualify it as an Arduino shield.
The "power pack" shield has the Arduino form factor though, with the matching 3 mounting holes, so it can be attached to the underside of an Arduino. (Note: Wiseduino's mounting holes are not aligned with those on Arduino 2009/Uno).
A schematic is not provided.


2. Li-Ion battery shield















It uses EUP8054 "linear Li-Ion battery charger with thermal regulation" chip. Schematic of the shield is provided here.
This battery shield does not come with a battery, but it has 6 big mounting holes that "can help you easily fix the battery pack". I could not find any photo (for inspiration) of the shield with batteries attached.
As shown in the photo above, the battery shield does not have the expansion female headers. It can be plugged into the Arduino, but no other shield plugged on top of it.


3. Solar charger shield V0.9















Seeedstudio discontinued this shield and replaced it with "Solar charger V2.0" (they also have a cheaper, non-shield version, the "Li-Po Rider").
This charger shield uses CN3083 chip. Schematic is published here and documentation can be found here.

The shield does not come with a battery, but it has the expansion headers installed. As expected, the ubiquitous, 68mm x 48mm flat Li-Ion 2000mAh battery (pictured connected to the shield in the photo above) does not fit between the headers, so stacking this shield only works with a smaller (both capacity and dimension-wise) type of battery, probably this 1000mAh one (50mm x 35mm x 5mm).

This battery shield would be the closest to my requirement, only if it had a battery.

Other battery chargers, shields or not, that I did not investigate yet are:

Comments

Post a Comment

Popular posts from this blog

How to Remove �Powered by Blogger� attribution From Blogspot Blog?

Image
                     Blogger initially add on every blog �Powered by Blogger" in Blogger footer. This dialogue called Attribution 1. It is optional and used to show copyright, credits and other information. You can remove this attribution widget and add your own information. Blogger not allow you directly to remove it because it is locked. If you have tried to remove this then you may of noticed this gadget is locked into you blog. There are three ways of removing "Powered by Blogger" from your BlogSpot blog. Method 1:  Using Unlock method Step 1. Log in to your Dashboard and go to your Blogger Dashboard. Step 2. Now go to Template > Edit HTML. Step 3. Tick the "Expand Widget Templates" checkbox. Step 4. Now Search (CTRL+ F) the following code: <b:widget id='Attribution1' locked='true' title='' type='Attribution'> Step 5. Replace true with false <b:widget id='Attribution1' locked='false' title='
Read more

Fritzing: an Electronic Design Automation software

Image
Fritzing is an open-source initiative to support designers, artists, researchers and hobbyists to take the step from physical prototyping to actual product. We are creating this software in the spirit of Processing and Arduino, developing a tool that allows users to document their Arduino and other electronic-based prototypes, and to create a PCB layout for manufacturing. The complementing website helps users to share and discuss drafts and experiences as well as to reduce manufacturing costs. Fritzing is essentially an Electronic Design Automation software with a low entry barrier, suited for the needs of designers and artists. It uses the metaphor of the breadboard, so that it is easy to transfer your hardware sketch to the software. From there it is possible to create PCB layouts for turning it into a robust PCB yourself or by help of a manufacturer. Why Fritzing is needed Physical prototyping tools have come a long way and already allow non-engineers to quickly turn their ideas in
Read more